基于电沉积法回收废水中铝离子的最佳工艺参数分析

基于电沉积法,针对某铝箔生产企业所产生的高含铝离子废水,通过不同峰值电流密度下形成的电沉积试样的相关电化学曲线测试结果和镀层中的Al质量分数分析,确定所采用电沉积法的最佳峰值电流密度为9 A·dm-2,此时沉积层中铝质量分数为33.21％,原子数量占比为24.69％.     

半轴齿轮的ABAQUS有限元模拟实验

车桥半轴齿轮是差速器的重要组成部分,在差速器工作中扮演着十分重要的角色.针对断裂的半轴齿轮进行断口形貌、成分及硬度分析,并结合有限元模拟分析齿轮失效的原因.结果表明:齿轮渗碳层厚度约0.8 mm,渗碳层显微组织主要为硬度较高的针状马氏体和部分残留奥氏体,硬度达785.1 N/mm2,表面硬化处理与渗碳处理基本符合工况要求.通过ABAQUS模拟发现半轴齿轮最易断裂处位于齿根最靠近边角的部位,与实际工况吻合.     

基于电机效率的纯电动汽车传动系统参数匹配研究

为降低能耗、提高续航里程,本文提出了以提高电机效率为目标的纯电动汽车三档变速传动方案.首先,在分析电机工作特性的基础上提出了三档传动系统参数匹配方法;然后以某纯电动汽车为研究对象,对其驱动系统进行了改动:方案一在不改变原车型动力系统参数的情况下将传动系统由一档改为三档,并运用所提出的方法确定各档位的传动比;方案二在满足整车动力性指标要求下对电机重新选型并匹配三档传动系统;最后利用ADVISOR软件进行NEDC工况仿真分析.结果表明:在不改变原车型动力系统参数的情况下,采用三档传动可使整车的动力性和经济性都有一定的提升,续航里程提高了 9.2％,百公里电耗降低了 1.28 kW·h;重新选型电机后,采用三档传动续航里程提高了 14.1％,百公里电耗降低了 1.87kW·h.     

石墨涂层载量对碱性锌锰电池电性能的影响

使用喷涂不同量石墨的钢壳组装碱性锌锰电池,考察石墨涂层载量对电池初始期及高温储存后电性能的影响.石墨涂层载量超过0.70 mg/cm2,会造成开路电压及放电性能下降,下降幅度随石墨涂层载量的增加及高温储存时间的延长而增大.     

气藏平均地层压力跟踪计算新方法

平均地层压力是产能评价和动态分析的基础，准确、快速获取平均地层压力对高效开发气藏意义重大。基于地层压力随时间变化的规律，分析了平均地层压力的变化规律。研究结果表明：平均地层压力等效点仅随时间发生改变，平均地层压力的下降速率等于或者近似等于井底流压的下降速率。从封闭弹性驱动气藏的物质平衡方程出发，考虑偏差系数和井底流压随平均地层压力的变化，推导建立了平均地层压力跟踪计算新方法，根据生产数据可迭代计算平均地层压力。方法验证结果显示，采气速度和采出程度共同影响模型的计算结果。应用实例表明，跟踪计算法与压力恢复试井和物质平衡法之间的相对误差均较小，满足工程计算精度要求，且跟踪计算法不需依托生产测试数据，节约了测试费用，避免了测试占产。     

Synthesis,Anticancer Activity,Structure-Activity Relationship and Mechanistic Investigations of Falcarindiol Analogues

Forty samples of optically active falcarindiol analogues are synthesized by using the easily available C2 symmetric (R)- and (S)-1,1’-binaphth-2-ol (BINOL) in combination with Ti(OⁱPr)₄, Zn powder and EtI. Their anticancer activities on Hccc-9810, HepG2, MDA-MB-231, Hela, MG-63 and H460 cells are assayed to elucidate their structure-activity relationships. These results showed that the falcarindiol analogue (3R,8S)- 2 i with the terminal double bond has the most potent anti-proliferation effect on Hccc-9810 cells with IC₅₀ value of 0.46 μM. The falcarindiol analogue (3R,8S)- 2 i can induce obvious Hccc-9810 cell apoptosis in a concentration-dependent manner by Hoechst staining and flow cytometry analysis. The proposed mechanism suggests that the falcarindiol analogue (3R,8S)- 2 i increases LDH release and MDA content, and reduces the levels of SOD activity, which lead to the accumulation of oxidative stress and induce apoptosis in Hccc-9810 cells.     

Tactile colour pictogram to improve artwork appreciation of people with visual impairments

A recent development in tactile technology enables an improvement in the appreciation of the visual arts for people with visual impairment (PVI). The tactile sense, in conjunction with, or a possibly as an alternative to, the auditory sense, would allow PVIs to approach artwork in a more self‐driven and engaging way that would be difficult to achieve with just an auditory stimulus. Tactile colour pictograms (TCPs), which are raised geometric patterns, are ideographic characters that are designed to enable PVIs to identify colours and interpret information by touch. In this article, three TCPs are introduced to code colours in the Munsell colour system. Each colour pattern consists of a basic cell size of 10 mm × 10 mm to represent the patterns consistently in terms of regular shape. Each TCP consists of basic geometric patterns that are combined to create primary, secondary, and tertiary colour pictograms of shapes indicating colour hue, intensity and lightness. Each TCP represents 29 colours including six hues; they were then further expanded to represent 53 colours. Two of them did not increase the cell size, the other increased the cell size 1.5 times for some colours, such as yellow‐orange, yellow, blue, and blue‐purple. Our proposed TCPs use a slightly larger cell size compared to most tactile patterns currently used to indicate colour, but code for more colours. With user experience and identification tests, conducted with 23 visually impaired adults, the effectiveness of the TCPs suggests that they were helpful for the participants.     

Additive Manufacturing of Stable Energy Storage Devices Using a Multinozzle Printing System

The development of the Internet of things has prompted an exponential increase in the demand for flexible, wearable devices, thereby posing new challenges to their integration and conformalization. Additive manufacturing facilitates the fabrication of complex parts via a single integrated process. Herein, the development of a multinozzle, multimaterial printing device is reported. This device accommodates the various characteristics of printing materials, ensures high-capacity printing, and can accommodate a wide range of material viscosities from 0 to 1000 Cp. Complete capacitors, inclusive of the current collector, electrode, and electrolyte, can be printed without repeated clamping to complete the preheating, printing, and sintering processes. This method addresses the poor stability issue associated with printed electrode materials. Furthermore, after the intercalation of LiFePO₄ with Na ions, X-ray photoelectron spectroscopy and X-ray diffraction results reveal that the Na ions permeate the interlayer structure of LiFePO₄, enhancing the ion migration channels by increasing the ion transmission rate. A current rate of 2.5 mAh ensures >2000 charge/discharge cycles, while retaining a charge/discharge efficiency of 96% and a discharge capacity of 91.3 mAh g⁻¹. This manufacturing process can provide conformal power modules for a diverse range of portable devices with various shapes, improving space utilization.     

综采超前轻便型运输单体柱滑道车的设计

基于超前支护影响作业面工作效率和职工健康,设计了综采超前轻便型运输单体柱滑道车.该型滑道车具有结构轻巧、使用方便、操作简单的特点,在燕子山矿得到推广应用.应用效果表明该滑道车具有制造简单、成本低、强度高、易于滑动、滑动稳定的特点,彻底改变了以往人工运输单体柱的方式,同时实现了工作面安全高效生产,创造了较高的经济效益.